[Free] 2018(June) Dumps4cert Cisco 400-151 Dumps with VCE and PDF Download 201-210
Dumps4cert.com : Latest Dumps with PDF and VCE Files
2018 May Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!
CCIE Data Center (v2.0)
Question No: 201 – (Topic 2)
Where is FIP negotiated?
-
between E Nodes and VF ports
-
between E Nodes and F Nodes
-
between VF ports
-
between VN ports
-
between VN ports and VF ports and FCFs Answer: E
Question No: 202 – (Topic 2)
Which two statements about end-host mode are true? (Choose two.)
-
In end-host mode, if a vNIC is hard pinned to an uplink port and this uplink port goes down, the system repms the vMIC, and the vNIC go
-
End-host mode allows the fabric in interconnect to act as an end host to the network, representing all servers (hosts) connected to it through vNICs.
-
End-host mode is the default Ethernet switching mode.
-
In end-host mode, the fabric interconnect runs the 5pann,ng Tree Protocol to avoid loops.
-
In end-host mode, if a vNIC is hard pinned to an uplink port and this uplink port goes down, the system repins the vNIC but the vNIC remain down until manual intervention.
Answer: B,C
Explanation: Ref: http://www.cisco.com/c/en/us/solutions/collateral/data-center- virtualization/unified-computing/whitepaper_c11-701962.html
Question No: 203 – (Topic 2)
Refer to the exhibit.
How many virtual adapters (vN|C and vHBA. can be added to this host?
A. 130
B. 128
C. 256
D. 258
Answer: C
Question No: 204 – (Topic 2)
Which three options are SDN Southbound protocols? (Choose 3)
-
Puppet
-
OVSDB
-
APl
-
OpenFlow
-
VXLAN
-
PCEP
Answer: B,D,F
Question No: 205 – (Topic 2)
Which description of how to enable DIMM Blacklisting is true?
-
Configure a memory policy in the equipment gt; policy subtab.
-
Enable blacklisting in the servers inventory gt; memory subtab.
-
Configure a memory policy under the services tab.
-
Enable blacklisting in the servers gt; policy subtab.
Answer: D
Question No: 206 – (Topic 2)
Which two statements about multicast routing are true? (choose two)
-
You can define RPF routes for multicast when you want multicast data to diverge from the unicast traffic path
-
Multicast routes are used to directly forward traffic without making RPF checks
-
You can define RPF routes for multicast on border routers to enable reverse path forwarding to an external network
-
RPF routes for multicast can be distributed
-
IPv6 static multicast routes are supported
Answer: A,C
Question No: 207 – (Topic 2)
Where is a typical request in the Cisco UCS XML API placed in the data management engine, and, after the request is confirmed, what is updated?
-
The request is placed in the transactor queue in FIFO order and the management information tree is updated.
-
The request is placed in the replicator and persistifier and the store is updated.
-
The request is placed in the data management engine and the application gateway is updated.
-
The request is placed in the buffer queue and the commit buffer queue is updated.
Answer: A
Question No: 208 – (Topic 2)
Which two statements about OpenStack are true? (Choose 2)
-
Horizon is the component that is used for IP address management.
-
Nova is the compute component that is used to manage and automate the provisioning of compute
resources.
-
Keystone is the networking component that is used to create and manage network resources.
-
Neutron is the networking component that is used to create and manage network resources.
-
Trove is the GUI web application that is used to control and configure different 0penStack components.
Answer: D,E
Question No: 209 – (Topic 2)
Which three PVLAN port modes are supported on Cisco Nexus 9000? (Choose three.)
-
port channels
-
isolated host trunk
-
FEX port
-
virtual port channels
-
isolated host
-
community host
Answer: B,E,F
Question No: 210 – (Topic 2)
On Cisco Nexus 1000v Switch, you can allow the VSM and VEM to communicate over IP for control and packet traffic.Before you create a port profile for Layer 3 control, which two statements must be verified? (Choose two)
-
Only one port profile can be configured with the capability Layer 3 control command.
-
All VEMs belong to the same Layer 2 domain.
-
The transport mode for the VSM domain should be configured as Layer 3.
-
The port profile must be a trunk port profile.
-
Different hosts should belong to the same VLANs for Layer 3 control. Answer: A,C
100% Dumps4cert Free Download!
–Download Free Demo:400-151 Demo PDF
100% Dumps4cert Pass Guaranteed!
–400-151 Dumps
Dumps4cert | ExamCollection | Testking | |
---|---|---|---|
Lowest Price Guarantee | Yes | No | No |
Up-to-Dated | Yes | No | No |
Real Questions | Yes | No | No |
Explanation | Yes | No | No |
PDF VCE | Yes | No | No |
Free VCE Simulator | Yes | No | No |
Instant Download | Yes | No | No |